\ Wireless Point to Point Ethernet Backhaul Bridges \ Up to 155Mbps Wireless Point to Point Ethernet Bridges \ 4.9-5.8 GHz Wireless Point to Point Ethernet Bridges, Up to 155 Mbps
Email This Page to a Friend
Exalt EX-5r 4xT1/E1 + 10/100BaseT; 100Mbps 5 GHz Tri-band Wireless Ethernet Bridge with dual pol. switched integrated antenna. Complete hop. PoE injector, accessory kit, 10' PoE CAT5 cable, and mounting kit. Order CAT-5 cable for Ethernet & T1/E1s separately
Winncom PN # E581002 Manufact PN # E581002 List Price: Login/Call Login and Stay on this page
The EX-5r wireless Ethernet bridges from Exalt Communications are the only tri-band 5GHz carrier-class wireless bridges available today. These all-outdoor systems operate in the 5.25-5.35 GHz, 5.4-5.725 GHz, and 5.725-5.850 GHz bands, and deliver up to 200Mbps of sustained user capacity and up to 4xT1/E1 in a software-configurable, carrier class system with high spectral efficiency, security and unprecedented spectrum management flexibility.
Along with the exceptional Ethernet capacity, the EX-5r provides up to four T1/E1 to enable PBX or trunk line interconnectivity and a seamless migration path from TDM to native IP-based services. In addition, the systems support SNMPv3 for the latest in secure network management support. For critical collocation applications and maximum spectrum reuse, the outdoor wireless Ethernet bridges from Exalt support GPS synchronization. And, to ensure the highest level of security, Exalt provides proprietary link security and AES encryption for the most demanding applications. Exalt’s breakthrough spectrum-management technology provides up to 54 non-overlapping frequency channels, with 1 MHz fine tuning capability across the three 5GHz bands. This results in as many as 415 center frequencies of operation to choose from without new hardware or system re-tuning. As an additional interference countermeasure, the EX-5r provides 8, 16, and 32 MHz channel bandwidths and synchronization to help maximize band usability and throughput. To support TDM to IP service migration strategies, the EX-5r and EX-5r-c provide a smooth upgrade path to higher T1/E1 capacities and Ethernet services. All this, while providing the lowest cost per megabit-mile of in its class. Specifications: System Frequency Band* 5250-5350MHz 5470-5725MHz 5725-5850MHz Tuning Resolution 1MHz Output Power (at full power)   5725-5850MHz band +24dBm, Mode 1 +21dBm, Mode 2 5470-5725MHz band +13dBm 5250-5350MHz band +13dBm Output Power (at min power) Full power minus 20 dB Power Control Step Size 0.5 dB Receiver Threshold (guaranteed over temperature @BER=10-6) Mode1 Mode2 8 MHz channel -86 dBm -78 dBm 16 MHz channel -83 dBm -75 dBm 32 MHz channel -80 dBm -72 dBm 64MHz channel** -77 dBm -69 dBm Receiver Threshold (typical) 2 dB better than above Maximum RSL (Mode 1) -25 dBm error-free, 0 dBm no damage Integrated Antenna*** Gain 20dBi 3dB Beamwidth 15 degrees Non-overlapping channels 8 MHz channel 10 29 15 16 MHz channel 5 14 7 32 MHz channel 2 7 3 64 MHz channel** 1 3 1 Aggregate User Capacity**** Mode1 Mode2 8 MHz channel 13 Mbps 27 Mbps 16 MHz channel 27 Mbps 55 Mbps** 32 MHz channel 55 Mbps 110 Mbps 64 MHz channel 110 Mbps 216 Mbps** Error Floor 10-12 Latency (T1) 1ms, typical Maximum packet size 1916 bytes Link Security 96-bit Security Key AES encryption** Management HTTP GUI, CLI/Telnet, SNMPv3 VLAN 802.1Q Regulatory Compliance FCC 15.247 FCC 15.407 IC RSS-210 Physical Physical Configuration Outdoor unit (ODU) Physical Configuration Dimensions (H x W x D) 13 x 13 x 4.25 inches (33 x 33 x 10.8 cm) Operating Temperature -40 to +65 degrees C -40 to +149 degrees F Full Spec Temperature -40 to +60 degrees C -40 to +140 degrees F Weight 14 pounds; 6.4 kg Environmental NEMA 4/IP56 Altitude 15,000 feet; 4.6 km Humidity 100% condensing Interfaces RF(x2) N-type Female, 50 ohm T1/E1 (x4) 2 x RJ48C/RJ45 (F) T1 Impedance 100 ohms, balanced T1 Line Codes AMI, B8ZS, selectable per channel T1 Clocking Speed 1.544Mbps T1 Compliance ANSI T1.102-1987 GR-49T-CORE E1 Impedance 120 ohms, balanced E1 Line Codes HDB3 E1 Clocking Speed 2.048 Mbps E1 Compliance CEPT-1; G.703; ITU-T-G703 Loopback Modes Remote Internal Remote External Local Line Ethernet RJ45 (F), auto-MDIX Interface Speed 10/100BaseT Duplex Half, Full, Auto Compliance 802.3 Sync (In) RJ45 (F) Signaling 1pps (GPS) AC Power Adapter Input 100-240VAC, 1.5A AC Power Adapter Output 48VDC, 1.5A, 72W via Power injector System Components Complete link Two terminals, each with AC adapter, accessory kit, and mounting kit Accessory kit Power injector, weatherproof connector, PoE cable, RSL antenna alignment cable, weatherproofing tape, and grounding hardware (spare) AC adapter AC adapter (spare) Mounting kits EX-5r mounting hardware (spare) GPS sync kit GPS antenna and mounting bracket (optional) *  Not all frequency bands are authorized or available for use in all countries. Consult your Exalt Communications representative for details. **  Firmware option required. ***  Integrated antenna (EX-5r) and external antenna version (EX-5r-c) both have user-selectable polarization switching. ****  The figure listed is the actual aggregate user throughput, maximum, as measured at layer 2. T1 or E1 circuits may be enabled one at a time, as needed, and subtract 3.1Mbps (1.544Mbps full-duplex) or 4.1Mbps (2.048Mbps full-duplex), respectively, from the aggregate user throughput. Some combinations of frame size, link distance, T1/E1 enabling, bandwidth, mode and desired latency will result in reduced maximum aggregate throughput. See your Exalt Communications representative for details.