\ Wireless Point to Point Ethernet Backhaul Bridges \ Up to 155Mbps Wireless Point to Point Ethernet Bridges \ 4.9-5.8 GHz Wireless Point to Point Ethernet Bridges, Up to 155 Mbps
Email This Page to a Friend
Exalt EX-5i-16 tri-band IDU, 4T1/E1 sw upgradeable to 16T1/E1+ 10/100; 100Mbps Wireless Backhaul Microwave Radio (32MHz/Mode2), 5.25-5.35 GHz, 5.4-5.725 GHz, and 5.725-5.850 GHz Frequency band; complete hop with AC adapters
Winncom PN # E580102 Manufact PN # E580102 List Price: Login/Call Login and Stay on this page
The EX-5i-16 wireless backhaul microwave radio from Exalt Communications is a new breed of all-indoor 5 GHz radio, specifically designed for demanding mobile backhaul applications requiring remote field-upgradeable capacity expansion. The EX-5i-16 is the only tri-band 5GHz digital microwave radio with software expandability from 4 to 16 T1/E1 plus 100BaseT. Operating in the 5.25-5.35 GHz, 5.4-5.725 GHz, and 5.725-5.850 GHz band, the EX-5i-16 is a carrier class system with minimal latency, high spectral efficiency, security, and unprecedented spectrum management flexibility.
The EX-5i-16 delivers maximum TDM capacity and IP functionality in one compact 1.5 RU package for the most demanding backhaul applications. Exalt’s breakthrough spectrum-management technology provides up to 54 non-overlapping frequency channels, with 1 MHz fine tuning capability across the three 5GHz bands. This results in as many as 415 center frequencies of operation to choose from without new hardware or system re-tuning. As an additional interference countermeasure, the EX-5i-16 provides 8, 16, and 32 MHz channel bandwidths and synchronization to help maximize band usability and throughput. And, to support TDM to IP service migration strategies, the EX-5i-16 provides a smooth upgrade path to higher T1/E1 capacities and Ethernet services. The system provides software expandability from 4 to 16 T1/E1 and a smooth upgrade path to higher capacity Ethernet services. TDM capacity may be conveniently expanded in groups of four ports via firmware option. All this, while providing the lowest cost per megabit-mile in the market today! Specifications: System Frequency Band* 5250-5350MHz 5470-5725MHz 5725-5850MHz Tuning Resolution 1 MHz Output Power (at full power) Mode 1 Mode 2 5725-5850MHz band +24 dBm +21 dBm 5250- 5350MHz band +13 dBm 5470-5725MHz band +13 dBm Output Power (at min power) Full power minus 20dB Power Control Step Size 0.5 dB Receiver Threshold (guaranteed over temperature @BER=10-6) Mode1 Mode2 8 MHz channel -86 dBm -78 dBm 16 MHz channel -83 dBm -75 dBm 32 MHz channel -80 dBm -72 dBm 64 MHz channel** -77 dBm -69 dBm Receiver Threshold (typical) 2db better Maximum RSL (Mode 1) -25 dBm error-free 0 dBm no damage Non-overlapping channels 5.3 GHz 5.4 GHz 5.8 GHz 8 MHz channel 10 29 15 16 MHz channel 5 14 7 32 MHz channel 2 7 3 64 MHz channel** 1 3 1 Aggregate User Capacity*** Mode1 Mode2 8 MHz channel 13 Mbps 27 Mbps 16 MHz channel 27 Mbps 55 Mbps 32 MHz channel 55 Mbps 110 Mbps 64 MHz channel** 110 Mbps 216 Mbps Max. Supported T1/E1 ports Mode1 Mode2 8 MHz channel 4/3 8/6 16 MHz channel 8/6 16/12 32 MHz channel 16/12 16/16 64 MHz channel** 16/16 16/16 Error Floor 10-12 Maximum packet size 1916 bytes Latency (T1) 1ms, typical Link Security 96-bit Security Key AES encryption** VLAN 802.1Q**** Management HTTP GUI, CLI/Telnet, SNMPv3*** Regulatory Compliance FCC 15.247 FCC 15.407 IC RSS-210 Physical Physical Configuration Single-piece Indoor Unit (IDU) Dimensions (H x W x D) 1.5 RU: 2.63 x 17 x 14 inches (6.7 x 43.2 x 35.6 cm) Operating Temperature -40 to +65 degrees C -40 to +149 degrees F Full Spec Temperature -25 to +60 degrees C -13 to +140 degrees F Weight 12 pounds; 5.5 kg Environmental GR-1089-CORE intra-building Altitude 15,000 feet; 4.6 km Humidity 95% non-condensing Interfaces RF N-type (F), Impedance: 50 ohms T1/E1 (x16)***** RJ48C/RJ45 (F) T1 Impedance 100 ohms, balanced T1 Line Codes AMI, B8ZS, selectable per channel T1 Clocking Speed 1.544Mbps T1 Compliance ANSI T1.102-1987 GR-499-CORE E1 Impedance 120 ohms, balanced E1 Line Codes HDB3 E1 Clocking Speed 2.048 Mbps E1 Compliance CEPT-1; G.703; ITU-T-G703 Loopback Modes Remote Internal Remote External Local Line Ethernet (x2) RJ45 (F), auto-MDIX Interface Speed 10/100BaseT Duplex Half, Full, Auto Compliance 802.3 Console (Serial) 9-pin Sub-D (F) Interface Speed 9600 bps Compliance EIA-574 (RS-232) Alarm 9-pin Sub-D (F) Inputs (2) TTL/Closure Outputs (2) Relay (Form C) Sync (In and Out) RJ45 (F) Signaling Internal Sync 1pps (GPS) **** DC Power 6-pin barrier strip Input Voltage ±20-60VDC Consumption <45W (48V :<0.9A, 24V:<1.8A) AC Power Adapter EIC-to-NEMA 5-15 Input 100-240VAC, 1.5A Output 48VDC, 1.5A, 72W System Components Complete link****** Two terminals each with AC adapter & accessory kit***** Single terminal One terminal with AC adapter & accessory kit Accessory kit DC power connector, rack and grounding hardware (spare) AC adapter AC adapter (spare) GPS sync kit**** GPS antenna and mounting bracket (optional) *  Not all frequency bands are authorized or available for use in all countries. Consult your Exalt Communications representative for details. **  Firmware option required ***  The figure listed is the actual aggregate user throughput, maximum, as measured at layer 2. T1 or E1 circuits may be enabled one at a time, as needed, and subtract 3.1Mbps (1.544Mbps full-duplex) or 4.1Mbps (2.048Mbps full-duplex), respectively, from the aggregate user throughput. Some combinations of frame size, link distance, T1/E1 enabling, bandwidth, mode and desired latency will result in reduced maximum aggregate throughput. See your Exalt Communications representative for details. ****  Firmware upgrade required *****  Capacity may be increased in groups of 4T1/E1 from 4 to 16 via separately purchased software option. ******  Two complete links (4 terminals) required for hot-standby protection along with protection kit and firmware option.