\ Wireless Point to Point Ethernet Backhaul Bridges \ Up to 155Mbps Wireless Point to Point Ethernet Bridges \ 4.9-5.8 GHz Wireless Point to Point Ethernet Bridges, Up to 155 Mbps
Email This Page to a Friend
Exalt EX-5i tri-band IDU, 4xT1/E1 + 10/100BaseT; 100Mbps; Wireless Backhaul Microwave Radio, 5.25-5.35 GHz, 5.47-5.725 GHz, and 5.725-5.850 GHz Frequency bands, complete hop with AC adapters
Winncom PN # E580002 Manufact PN # E580002 List Price: Login/Call Login and Stay on this page
The EX-5i wireless backhaul microwave radio from Exalt Communications is a new breed of indoor 5 GHz radio. The EX-5i is a 5GHz tri-band system operating in the 5.25-5.35 GHz, 5.47-5.725 GHz, and 5.725-5.850 GHz bands, with 200Mbps user-throughput in a software-defined, carrier class system with high spectral efficiency, security, and unprecedented spectrum management flexibility.
Along with the 200 Mbps of user-throughput data capacity, the EX-5i provides up to four T1/E1 interfaces to enable PBX or trunk line interconnectivity and a seamless migration path from TDM to native IP-based services. Exalt’s breakthrough spectrum-management technology provides up to 54 non-overlapping frequency channels, with 1 MHz fine tuning capability across the three 5GHz bands. This results in as many as 415 center frequencies of operation to choose from without new hardware or system re-tuning. As an additional interference countermeasure, the EX-5i provides 8, 16, and 32 MHz channel bandwidths to help maximize band usability and throughput (64MHz channel bandwidth is available as a software option). And, to support TDM to IP service migration strategies, the EX-5i provides a smooth upgrade path to higher T1/E1 capacities and Ethernet services. All this, while providing the lowest cost per megabit-mile in the market today! Specifications: System Frequency Band* 5250-5350MHz 5470-5725MHz 5725-5850MHz Tuning Resolution 1MHz Output Power (at full power) Mode 1 Mode 2 5725-5850MHz band +24 dBm +21 dBm 5250-5350MHz band +13dBm 5470-5725MHz band +13dBm Output Power (at min power) Full power minus 20 dB Power Control Step Size 0.5 dB Receiver Threshold (guaranteed over temperature @BER=10-6) Mode1 Mode2 8 MHz channel -86 dBm -78 dBm 16 MHz channel -83 dBm -75 dBm 32 MHz channel -80 dBm -72 dBm 64 MHz channel** -77 dBm -69 dBm Maximum RSL (Mode 1) -25 dBm error-free 0 dBm no damage Non-overlapping channels 5.3GHz 5.4GHz 5.8GHz 10 29 15 5 14 7 2 7 3 1 3 1 8 MHz channel 16 MHz channel 32 MHz channel 64 MHz channel** Aggregate User Capacity*** Mode1 Mode2 8 MHz channel 13 Mbps 27 Mbps 16 MHz channel 27 Mbps 54 Mbps 32 MHz channel 55 Mbps 110 Mbps 64 MHz channel 110 Mbps 216 Mbps Error Floor 10-12 Latency (T1) 1ms, typical Maximum packet size 1916 bytes Link Security 96-bit Security Key AES encryption** VLAN 802.1Q Management HTTP GUI, CLI/Telnet, SNMPv3 Regulatory Compliance FCC 15.247 FCC 15.407 IC RSS-210 Physical Physical Configuration Single-piece Indoor Unit (IDU) Dimensions (H x W x D) 1RU: 1.75 x 17 x 14 inches (4.5 x 43.2 x 35.6 cm) Operating Temperature -40 to +65 degrees C -40 to +149 degrees F Full Spec Temperature --25 to +60 degrees C -13 to +140 degrees F Weight 11.3 pounds; 5.1 kg Environmental GR-1089-CORE intra-building Altitude 15,000 feet; 4.6 km Humidity 95% non-condensing Interfaces RF N-type (F), Impedance: 50 ohms T1/E1 (x4) RJ48C/RJ45 (F) T1 Impedance 100 ohms, balanced T1 Line Codes AMI, B8ZS, selectable per channel T1 Clocking Speed 1.544Mbps T1 Compliance ANSI T1.102-1987 ITU-T; G.823; GR-49T-CORE E1 Impedance 120 ohms, balanced E1 Line Codes HDB3 E1 Clocking Speed 2.048 Mbps E1 Compliance CEPT-1; G.703; ITU-T-G703 Loopback Modes Remote Internal Remote External Local Line Ethernet (x2) RJ45 (F), auto-MDIX Interface Speed 10/100BaseT Duplex Half, Full, Auto Compliance 802.3 Console (Serial) 9-pin Sub-D (F) Interface Speed 9600 bps Compliance EIA-574 (RS-232) Alarm 9-pin Sub-D (F) Inputs (2) TTL/Closure Outputs Outputs Sync (In and Out) RJ45 (F) Signaling 1pps (GPS)**** DC Power 6-pin barrier strip Input Voltage Input Voltage Consumption <0.7A @ 48V, <34W AC Power Adapter EIC-to-NEMA 5-15 Input 100-240VAC, 1.5A Output 48VDC, 1.5A, 72W System Components Complete link Two terminals each with AC adapter & accessory kit Single terminal One terminal with AC adapter & accessory kit Accessory kit DC power connector, rack and grounding hardware (spare) AC adapter AC adapter (spare) *  Not all frequency bands are authorized or available for use in all countries. Consult your Exalt Communications representative for details. **  Firmware option required. ***  The figure listed is the actual aggregate user throughput, maximum, as measured at layer 2. T1 or E1 circuits may be enabled one at a time, as needed, and subtract 3.1Mbps (1.544Mbps full-duplex) or 4.1Mbps (2.048Mbps full-duplex), respectively, from the aggregate user throughput. Some combinations of frame size, link distance, T1/E1 enabling, bandwidth, mode and desired latency will result in reduced maximum aggregate throughput. See your Exalt Communications ****  Firmware upgrade required representative for details.