Operating in the 2400 to 2483.5 MHz ISM band, the EX-2.4i extends the advantages of this band for high capacity, long range wireless backhaul applications.
Along with 100Mbps of user throughput data capacity, the EX-2.4i provides up to four T1/E1 interfaces to enable PBX or trunk line interconnectivity and a seamless migration path from TDM to native IP-based services.
Exalt’s breakthrough spectrum-management technology provides up to eight non-overlapping frequency channels, with 1MHz fine tuning capability across the entire band. This results in as many as 62 center frequencies of operation without new hardware or system re-tuning. As an additional interference countermeasure, the EX-2.4i provides 8, 16, and 32 MHz channel bandwidths to help maximize band usability and throughput. And, to support TDM to IP service migration strategies, the EX-2.4i provides a smooth upgrade path to higher T1/E1 capacities and Ethernet services without replacing existing transmission systems. All this, while providing the lowest cost per megabit-mile in the market today!
Specifications:
|
System |
|
Frequency Band |
2400 to 2483.5MHz |
|
Tuning Resolution |
1 MHz |
|
Output Power (at full power) |
Mode 1 |
Mode 2 |
| +27 dBm |
+24 dBm |
|
Output Power (at min power) |
+ 7 dBm |
|
Power Control Step Size |
0.5 dB |
|
Receiver Threshold (guaranteed over temperature @BER=10-6) |
Mode1 |
Mode2 |
|
8 MHz channel |
-88 dBm |
-80 dBm |
|
16 MHz channel |
-85 dBm |
-77 dBm |
|
32 MHz channel |
-82 dBm |
-74 dBm |
|
64 MHz channel* |
-79 dBm |
-71 dBm |
|
Maximum RSL (Mode 1) |
-25 dBm error-free 0 dBm no damage |
|
Non-overlapping channels |
|
8 MHz channel |
8 |
|
16 MHz channel |
4 |
|
32 MHz channel |
2 |
|
64 MHz channel* |
1 |
|
Aggregate User Capacity** |
Mode1 |
Mode2 |
|
8 MHz channel |
13 Mbps |
27 Mbps |
|
16 MHz channel |
27 Mbps |
54 Mbps |
|
32 MHz channel |
55 Mbps |
110 Mbps |
|
64 MHz channel* |
110 Mbps |
216 Mbps |
|
Error Floor |
10-12 |
|
Latency (T1) |
1ms, typical |
|
Link Security |
96-bit Security Key AES encryption* |
|
VLAN |
802.1Q |
|
Management |
HTTP GUI, CLI/Telnet, SNMPv3*** |
|
Regulatory Compliance |
FCC 15.247
IC RSS-210 |
|
Physical |
|
Physical Configuration |
Single-piece Indoor Unit (IDU) |
|
Dimensions (H x W x D) |
1RU: 1.75 x 17 x 14 inches (4.5 x 43.2 x 35.6 cm) |
|
Operating Temperature |
-40 to +65 degrees C
-40 to +149 degrees F |
|
Full Spec Temperature |
-40 to +60 degrees C
-40 to +140 degrees F |
|
Weight |
11.3 pounds; 5.1 kg |
|
Environmental |
NEMA 4/IP56 |
|
Altitude |
15,000 feet; 4.6 km |
|
Humidity |
95% non-condensing |
|
Environmental |
GR-1089-CORE intrabuilding |
|
Interfaces |
|
RF |
N-type (F), Impedance: 50 ohms |
|
T1/E1 (x4) |
RJ48C/RJ45 (F) |
|
T1 Impedance |
100 ohms, balanced |
|
T1 Line Codes |
AMI, B8ZS, selectable per channel |
|
T1 Clocking Speed |
1.544Mbps |
|
T1 Compliance |
ANSI T1.102-1987
ITU-T; G.823;
GR-49T-CORE |
|
E1 Impedance |
120 ohms, balanced |
|
E1 Line Codes |
HDB3 |
|
E1 Clocking Speed |
2.048 Mbps |
|
E1 Compliance |
CEPT-1; G.703; ITU-T-G703 |
|
Loopback Modes |
Remote Internal
Remote External
Local Line |
|
Ethernet (x2) |
RJ45 (F), auto-MDIX |
|
Interface Speed |
10/100BaseT |
|
Duplex |
Half, Full, Auto |
|
Compliance |
802.3 |
|
Console (Serial) |
9-pin Sub-D (F) |
|
Interface Speed |
9600 bps |
|
Compliance |
EIA-574 (RS-232) |
|
Alarm |
9-pin Sub-D (F) |
|
Inputs |
(2) TTL/Closure |
|
Outputs |
Outputs |
|
Sync (In and Out) |
RJ45 (F) |
|
Signaling |
1pps (GPS)*** |
|
DC Power |
6-pin barrier strip |
|
Input Voltage |
Input Voltage |
|
Consumption |
<0.7A @ 48V, <34W |
|
AC Power Adapter |
EIC-to-NEMA 5-15 |
|
Input |
100-240VAC, 1.5A |
|
Output |
48VDC, 1.5A, 72W |
|
System Components |
|
Complete link |
Two terminals each with AC adapter & accessory kit |
|
Single terminal |
One terminal with AC adapter & accessory kit |
|
Accessory kit |
DC power connector, rack and grounding hardware (spare) |
|
AC adapter |
AC adapter (spare) |
|
GPS sync kit*** |
GPS antenna and mounting bracket (optional) |
* Firmware option required
** The figure listed is the actual aggregate user throughput, maximum, as measured at layer 2. T1 or E1 circuits may be enabled one at a time, as needed, and subtract 3.1 Mbps (1.544 Mbps full-duplex) or 4.1 Mbps (2.048 Mbps full-duplex), respectively, from the aggregate user throughput. Some combinations of frame size, link distance, T1/E1 enabling, bandwidth, mode and desired latency will result in reduced maximum aggregate throughput. See your Exalt Communications representative for details.
*** Firmware upgrade required.