The AP Module operates with a raw data rate of 10 Mbps and has a range of approximately ten miles (5.7 GHz SM with reflector). Each AP requires a 24-volt power Configuration Guide source and uses a single 10/100 BaseT Half/Full duplex connection to interface into the CMM or appropriate network connection. |
| Package Includes: |
| P/N |
Description |
Quantity |
| 5700APC |
5.7 GHz UK Connectorized Adj Power |
1 |
| ACPSSW-02 |
90-230VAC Power Supply-Euro |
Not Included |
| SMMB1 |
Canopy Universal Mounting Bracket |
Not Included |
AP Module Specifications:
| Description |
5.7 GHz UK Connectorized Adj Power |
| Canopy Part Number |
5700APC |
| Market Availability |
UK and Europe |
| Signaling Rate |
10 Mbps |
| Typical LOS Range |
2 Mi (3.2 km) |
| Typical Aggregate Useful Throughput |
6.2 Mbps |
| Frequency range of band |
ISM 5725-5850 MHz |
| Non-overlapping Channels |
6 |
| Channel Width |
20 MHz |
| Channel Spacing |
every 5 MHz |
| Modulation Type |
High Index 2-level Frequency Shift Keying (FSK) optimized for interference rejection |
| Encryption |
DES capable |
| Latency |
15 msec |
| Carrier to Interference ratio (C/I) |
~3dB @ 10 Mbps, ~10dB @ 20 Mbps at -65dBm |
| Nominal Receiver Sensitivity (dbm typical) |
-86 dB |
| EIRP (dB) |
Adjustable |
| Equivalent Isotropic Radiated Power (EIRP) |
Adjustable to 1W |
| DC Power (typical) |
0.3 A @ 24 VDC = 7.2 W |
| Antenna Beam Width |
3 dB antenna beam width 60 degrees, Azimuth and Elevation |
| Temperature |
-40° C to +55° C (-40° F to +131° F) |
| Dimensions |
11.75 in H x 3.4 in W x 3.4 in D (29.9 cm H x 8.6 cm W x 8.6 cm D) |
| Weight |
.45 kg (1 lb) |
| Access Method |
Time Division Duplexing/Time Division Multiple Access (TDD/TDMA) |
| Interface |
10/100 Base T, half/full duplex. Rate auto negotiated (802.3 compliant) |
| Protocols Used |
IPV4, UDP, TCP, ICMP, Telnet, HTTP, FTP, SNMP |
| Network Management |
HTTP, TELNET, FTP, SNMP Version 2c |
| FCC ID |
ABZ89FC5804 |
| Industry Canada Certification Number |
109W-5700 |
Access Point (AP) Cluster
The AP Cluster is a base station that can incorporate between one and six AP Modules and up to two Backhaul Modules (BH). Each module operates with a 60-degree directional antenna to provide coverage to one sector. One of the unique capabilities of the Canopy system is its ability to synchronize the transmission timing of the AP Modules in all of the AP Clusters. The GPS receiver in the CMM is the key to delivering this system level synchronization. The synchronization of the AP transmission along with the specially designed Canopy Time Division Duplex (TDD) air interface ensures that all AP Modules transmit at the same time while all Subscriber Modules (SM) are in a listen mode. This synchronization also ensures that when the SMs are transmitting, all the AP Modules are listening. This synchronization, enabled by the Cluster Management Module (CMM), ensures that the Canopy system does not interfere with itself, since the AP Modules do not interfere with each other and the SMs do not interfere with each other. This unique characteristic delivers an ability to scale the network where Canopy AP Clusters can be added to the network to improve system coverage or capacity without increasing the system interference.
AP Cluster with GPS Antenna
|